One motor spinning too slow?? - Discussions - diydrones
Aug 29, 2019 · My motor number 4 is always running slower and somewhat later than the other three motors. Tried calibrating and recalibrating the esc multiple times. Still problem persists. Tried changing esc, motor, motor mount screws, and the pixhawk, but all in vain. if anyone could guide me what to do, or if someone faced similar issue, help me out.
Motor spin slow than others - ArduCopter User Group - diydrones
Apr 29, 2013 · Hello, all , im working with APM 2.5, in X configuration, when i arm the APM, one motor (motor 4) spin slow than others 3. When i calibrate the ESC's in automatic mode, all spin with same speed and work fine, but when
One motor requires more throttle to start spinning
Jul 10, 2014 · Hi, I've got one motor on my 3DR Y6 that won't spin during a motor test, or when the drone is armed and MOT_SPIN_ARMED is set to "Slow". All other motors respond to the test and the arming just fine. However, if I give the drone a little throttle with my Tx, the other motors start to speed up, then at some point as throttle increases the motor in question begins to spin as well. Are there ...
APM 2.8 Armed (solid Red LED) but motors spinning slow
Aug 11, 2018 · Dear i am a beginner i have set up each and every thing but when i armed my quad copter . motor no 1 satrt spining after 50% throttle whereas other 3 motors does not start spin but when i move my pitch than one of my motor start spinning too but my other two motors were not spinning .yet....than i connect my apm through usb and set the pre arm check to 0 . but nothing happen and my motor spin ...
Motors spinning at zero throttle - Discussions - diydrones
Jul 23, 2014 · Its a long list and has a name like "Advanced parameters". The parameter (sorry cant remember the name) takes a value that starts at 0. You most likely have it set to a non zero value which results in a slow span. Bigger numbers mean faster spinning on …
Stop Motor spinning during taking a photo / automission
Feb 23, 2016 · For long gaps between images simply add an extra waypoint near to the intended point but at a higher altitude. the aircraft will climb to the new height and then descend slightly to the photo height with a slow motor. The much better solution is to balance the props as Andre K suggests. Better for the pixhawk as well as you aircraft and camera.
Best flight times, electric vs nitro...etc.(plane)? - diydrones
Jan 30, 2016 · We have got more than 4 hours on the Raptor E1 using a 26,000mah 6 S lipo and custom made large diameter propellers on a slow spinning motor. Best Anton Rada January 24, 2014 at 3:03am
[SOLVED] One motor on quad begins spinning later...
Aug 12, 2015 · I use an APM 2.5 running arducopter FW 3.1. It has flown for many months very well. After a crash which broke the micro usb port off the circuit board, one of the motors begins to spin only after the other three are at nearly 15%. I can take off, but the one ESC/motor combination does not provide as much thrust as the other three which seem quite balanced. Once I switch to loiter mode, the ...
Pixhawk hexacopter build, Motors spin slow on full throttle
Jun 25, 2014 · Hello, I'm building a hexacopter with a Tarot T960 frame and a Pixhawk. Here are my other components: HobbyKing 40A BlueSeries Brushless Speed Controllers iPower MT4114 320kv 17x55 props 6s Lipo I've built the thing and gone through ESC calibration without issue. I can also get it to arm just fine. However when I go to fly. I arm it and it the motors spin up just fine. However, when I bring ...
One Motor Intermittently Runs Slowly? - Discussions - diydrones
Jul 5, 2013 · I am having a perplexing problem with my Quad. Often when I run up the motors from an armed but stopped state, one motor runs mush slower, perhaps 1/4 the speed, of the other three. It is always the same motor, the right side motor on APM 2.0 channel 1. If I shut off throttle and bring it back up, eventually they all start correctly. It might take one try, or 10. Once running correctly ...